Free tool
Generator maintenance checklist
Inspect a standby generator every week. Run it every month for at least 30 minutes at 30 percent of nameplate load, or at the maker’s minimum exhaust temperature, and operate the transfer switch. Test diesel fuel twice a year, add an annual load bank test if the monthly load falls short, and run a 4-hour test every 36 months on Level 1 systems (life-safety loads such as egress lighting, fire alarms and fire pumps). Fill in the checklist below, then download it as a PDF (filled or blank) or an Excel file. Morsa asks for each check and flags a missed or failed one.
Updated November 12, 2026
Generator maintenance schedule at a glance
| How often | What to do | Source |
|---|---|---|
| Weekly | Inspect fuel, oil, coolant, exhaust, battery, wiring, the set itself | NFPA 110 as cited by Minnesota DOH |
| Monthly | Run 30 minutes at 30% of nameplate, cold start, transfer switch operation | NFPA 110 (Cummins reprint) |
| Twice a year | Test diesel fuel for degradation, 6 months apart | NFPA 110 (Cummins reprint) |
| Yearly | Load bank if needed, breaker exercise, filters and oil, infrared scan | NFPA 110, Kohler |
| Every 36 months | Level 1: continuous test up to 4 hours | NFPA 110 (Cummins reprint) |
We did not read the current NFPA 110 itself. We read its 2016 text as reprinted by Cummins and Minnesota Department of Health’s guidance. Later editions may differ; use the edition your authority adopts.
How to use the generator maintenance checklist
Enter the generator number and the run hours.
Pick the checklist that is due and mark each check Done, Issue or N/A. Fuel, battery, monthly run and transfer switch checks cannot be marked N/A.
Write the readings and what is wrong against failed items.
Download the PDF (filled or blank) for the generator room, or the Excel file for the test log.
NFPA 110: what the standard says about testing
Monthly run. Generator sets in service “shall be exercised at least once monthly, for a minimum of 30 minutes”, using loading that holds the maker’s minimum exhaust gas temperature, or operating temperature and “not less than 30 percent of the EPS standby nameplate kW rating”. A 100 kW set needs at least 30 kW. Warm-up and cool-down time do not count toward the 30 minutes.
If the load falls short. Diesel sets that cannot meet this are exercised monthly with the available load and annually with supplemental loads at 50 percent for 30 minutes and 75 percent for 1 hour, 1.5 hours in all.
Transfer switches “shall be operated monthly”.
Fuel. A fuel quality test at least annually using ASTM methods, and diesel fuel tested for degradation “no less than twice annually with a minimum of 6 months between testing”.
Batteries are inspected weekly, and lead-acid batteries get a monthly specific gravity test, or conductance testing instead.
Level 1 systems (where failure could cost lives or cause serious injury) are tested at least once every 36 months, continuously for the assigned class and up to 4 hours.
Is NFPA 110 required for your generator?
NFPA 110 is a standard, and it binds where a code, a licence or an inspector adopts it. Minnesota’s health department says hospitals must inspect weekly and exercise under load monthly to meet federal certification and state licensure, and that NFPA 99 requires 12 tests a year, 20 to 40 days apart. Many data centers and plants use NFPA 110 as the benchmark without a legal duty. Ask your insurer and inspector which edition and level applies.
Type 10, levels and the EPA 100-hour limit
Type 10. NFPA 110 types say how long the transfer switch load can be without acceptable power. Type 10 means 10 seconds. Minnesota’s guide adds that NFPA 101 requires emergency loads picked up within 10 seconds. Other codes decide which type applies.
Which level is a data center? NFPA 110 applies to Level 1 and Level 2 systems, and does not say which of your loads fall in each; other codes decide. It also does not cover NEC Article 702 optional standby systems. We found no source that assigns a level to a data center load, so ask your inspector.
EPA hours. Under 40 CFR 63.6640(f), an emergency engine may run for maintenance checks and readiness testing up to 100 hours per calendar year, if the tests are recommended by government, the manufacturer, the vendor or the insurer. Twelve 30-minute monthly runs are 6 hours. Your air permit may set its own limits.
Generator oil, filter and coolant intervals
NFPA 110 leaves these to the maker. Two manuals for small sets show how much they differ. Large standby sets, data center size, set oil, coolant and filter intervals in their own manuals; ask the maker for the schedule at your hours and duty.
| Example from a small set | Oil and filter | Other |
|---|---|---|
| Generac Protector diesel | Every 2 years or 250 hours, whichever first | Air filter yearly or 125 hours; coolant flush every 2 years or 250 hours |
| Cummins home standby | First 25 and 100 hours, then every 200 hours or 2 years | Air filter every 200 hours or 2 years |
From each owner’s manual for standby duty. Shorten intervals in hot, dusty or extreme conditions. Your own manual decides.
Where the generator sources disagree
Oil change intervals differ by model and duty. Minnesota’s guide cites an older NFPA 110 edition than Cummins’s reprint, and 12 tests a year is an NFPA 99 healthcare rule. We used NFPA 110’s minimums and the maker’s intervals, whichever is stricter.
What to do when a generator check fails
Fails to start, low oil, fuel problem, battery fault: treat the building as unprotected. Call your service provider and tell the facility lead.
Before service, disable it. Cummins says to put the set in Off, disable the battery charger and remove the negative battery cable so it cannot start. Lock out under your program, OSHA 29 CFR 1910.147.
Fuel test fails: polish or replace the fuel as the lab and the maker advise.
Write the reading on the checklist and open a work order. See the work order template.
Generator maintenance mistakes
Running it unloaded. Light loads miss the 30% or exhaust temperature rule.
Skipping the transfer switch. The set can run fine and still never take the load.
No fuel testing. Diesel degrades while it sits.
Letting the battery go. Cummins says a significant share of generator set failures are battery issues.
No record. Inspectors and insurers ask for the test log.
Keeping the generator tests on schedule
Morsa asks the facilities lead for the weekly inspection and the monthly run results in WhatsApp, Teams, text or email, and files them against the generator. It records run time and the load percent, flags a monthly run that is late or came in under 30%, and schedules the load bank, fuel tests and the 36-month test for approval.
Other maintenance checklists
Preventive maintenance checklist: the hub, a general PM checklist for any machine
UPS maintenance checklist: batteries, bypass and firmware
Chiller maintenance checklist: daily readings and annual service
Cooling tower maintenance checklist: water treatment and Legionella
Plant shutdown checklist: phases from planning to restart
Frequently asked questions
What should be on a generator maintenance checklist?
Weekly inspection of fuel, oil, coolant, exhaust, battery and wiring, a monthly loaded run and transfer switch test, fuel testing, filters, and a yearly load bank if needed.
How often should a generator be run?
NFPA 110 says at least monthly, for 30 minutes, at 30 percent of nameplate load or the maker’s minimum exhaust temperature.
How often should a commercial generator be serviced?
Inspect weekly, test monthly, service oil and filters at the maker’s interval, and test fuel twice a year. Level 1 systems also run a long test every 36 months.
What is a load bank test?
A run with an added resistive load. NFPA 110 requires one annually for diesel sets that cannot reach 30 percent: 50 percent for 30 minutes, then 75 percent for an hour.
How often should generator oil be changed?
At the maker’s interval. Two small sets differ: every 250 hours or 2 years on one Generac diesel, every 200 hours or 2 years on one Cummins. Large sets have their own schedules, so ask the maker.
Does a data center generator have to follow NFPA 110?
Only where a code or authority adopts it, but it is the usual benchmark. Ask your inspector and insurer which edition and level apply.
Related tools
Sources
Kohler, Guide to Maintenance for Power Generation Equipment (read November 12, 2026)
Generac, Protector Series diesel owner’s manual (read November 12, 2026)
Cummins Power Generation, home standby generator operator manual (read November 12, 2026)
eCFR, 40 CFR 63.6640(f), Emergency stationary RICE operating limits (read November 12, 2026)
OSHA, 29 CFR 1910.147, The control of hazardous energy, osha.gov (read November 12, 2026)
Where Morsa fits
Prove every test was done and logged.
Morsa asks for the weekly inspection and monthly run results, files them against the generator and flags a missed test or a low load. It works in whatever your team runs on: WhatsApp, Teams, email or text.

