Free tool
Air compressor maintenance checklist
Every day, check the oil level, read the display and drain the condensate. Every week, check drains, leaks and line filters. Change the oil, oil filter and separator every 4,000 hours or yearly (Atlas Copco GA 15 to 30, mineral fluid, room under 25 C; other makes and fluids differ). Inspect the receiver yearly and test the safety valve at the maker’s interval (Atlas Copco: 8,000 hours or 2 years). Fill in the checklist below, then download it as a PDF (filled or blank) or an Excel file. Morsa asks for it on schedule and flags a missed or failed check.
Updated November 12, 2026
Air compressor maintenance schedule at a glance
| How often | What to check | Why |
|---|---|---|
| Daily | Oil level, display readings, condensate drain, filter indicator | Low oil or a flooded receiver damages the unit fastest |
| Weekly | Drain traps, air leaks, line filter pressure drop, cooler dust | Stuck drains and leaks waste air; clogged filters waste power |
| Monthly or every 400 run hours | Belts, separator pressure drop, motor cooling fins, a readings log | Belts stretch; the log shows drift before a failure |
| Every 3 months | Coolers, air filter element, cabinet filter, dryer filters | Dust and heat shorten oil and element life |
| Every 4,000 hours or yearly | Oil, oil filter, separator, air filter, electrical connections | The main service on an Atlas Copco GA 15 to 30 |
| Yearly | Receiver inspection, every line filter element, a review of the year | Pressure-vessel and efficiency items |
| 8,000 hours or 2 years | Safety valve test, minimum pressure and thermostatic valves, scavenge non-return valve | Atlas Copco Table 2 and the OSHA safety valve rule |
Daily, 3-month, 4,000-hour and 8,000-hour intervals are from the Atlas Copco GA 15 to 30 instruction book. The limits in the weekly and monthly rows are from DOE and the Compressed Air Challenge. Grouping them by week and month is our choice.
How to use the air compressor maintenance checklist
Enter the compressor number and the run hours from the display. Hours, not the calendar, drive the big services.
Pick the checklist that is due and work down it: mark each check Done, Issue or N/A. Core checks, like the oil level and the temperature shutdown test, cannot be marked N/A.
Write what is wrong against any failed item, with the reading.
Download the PDF (filled or blank) for the compressor room, or the Excel file to load into your maintenance system.
Industrial air compressor maintenance: the numbers that matter
Most checklists say “replace filters regularly”. These limits come from sources we read, so a technician knows when regularly means now.
| Check | Limit | Source |
|---|---|---|
| Line filter pressure drop | Replace the element at 2 to 3 psid | Compressed Air Challenge |
| Oil separator pressure drop | Change at 10 psid, or the manual’s interval if sooner | Compressed Air Challenge |
| Dirty coalescing filter | Up to 6 psi drop against 2 psi clean; each 2 psi costs about 1% of capacity | US DOE tip sheet 6 |
| Belts | Examine and adjust every 400 hours of operation | Compressed Air Challenge |
| Leakage | Under 5 to 10% of capacity is good; 20 to 30% is a poorly maintained plant | US DOE sourcebook |
| Roto-Inject Fluid Ndurance (mineral) | 4,000 h up to 25 C ambient, 3,000 h at 25 to 35 C, 2,000 h above 35 C, and at most 1 year | Atlas Copco GA 15 to 30 |
| Roto Synthetic Fluid Xtend Duty | 8,000 h up to 40 C ambient, 6,000 h above, and at most 2 years | Atlas Copco GA 15 to 30 |
| Roto Synthetic Fluid Ultra | 6,000 h up to 35 C, 4,000 h at 35 to 40 C, 2,000 h at 40 to 45 C, and at most 2 years | Atlas Copco GA 15 to 30 |
psid is pounds per square inch of pressure drop across the part. One maker’s schedule, fluid by fluid; the manual’s fluid section uses slightly different bands for the mineral fluid. Use your own manual.
The Compressed Air Challenge adds that manufacturer intervals “are primarily designed to protect equipment”, so it can pay to service filters and separators sooner than the manual says, especially when power is expensive.
What to do when an air compressor check fails
Safety valve will not lift, oil level gone, or temperature shutdown fails: stop the unit and tag it out. Do not run it to finish the shift.
Before any repair, isolate it. OSHA 29 CFR 1910.147 requires the machine to be shut down in an orderly way, isolated, locked or tagged out, and stored energy relieved. Atlas Copco’s own list adds: press the emergency stop, close the air outlet valve, and depressurize.
Verify before you touch it. 1910.147(d)(6) says to verify that isolation and deenergization have been accomplished before work starts.
Write the fault and the reading on the checklist, tell the maintenance lead, and open a work order. See the work order template.
The receiver rules OSHA sets
OSHA 29 CFR 1910.169 covers air receivers. The drain valve “shall be opened and the receiver completely drained frequently”, every receiver needs a readable pressure gauge and a spring-loaded safety valve, “no valve of any type shall be placed between the air receiver and its safety valve”, and safety valves “shall be tested frequently and at regular intervals”. It does not give an interval in days, so write yours into the checklist and keep the record. State and insurer rules on pressure-vessel inspection vary; ask yours.
Mistakes that make compressor maintenance fail
Servicing by the calendar only. A compressor running 24 hours a day reaches 4,000 hours in about 167 days (4,000 divided by 24). Track run hours.
Ignoring the room. Heat shortens the oil interval and dust clogs coolers and filters.
Trusting auto drains. A drain stuck open blows air all day; one stuck closed floods the dryer. Test them.
No leak program. At 20 to 30% leakage you are running a compressor for air that never reaches a tool.
Wrong lubricant or parts. Use only the fluid the manual names. Atlas Copco says damage from unauthorized parts is not covered by warranty.
No baseline. Without a record of pressure, temperature and amps on a good day, drift cannot be seen.
Other maintenance checklists
Preventive maintenance checklist: the hub, a general PM checklist for any production machine
CNC machine maintenance checklist: way lube, coolant concentration and backlash checks
Conveyor maintenance checklist: belts, rollers and drives
Generator maintenance checklist: weekly, monthly and annual tests
Chiller maintenance checklist: daily readings and tube cleaning
Frequently asked questions
How often should an air compressor be serviced?
Daily and weekly checks, then the big service by hours: every 4,000 hours or yearly on an Atlas Copco GA 15 to 30 with mineral oil. Your manual sets the exact figure.
How often should you change the oil in a rotary screw air compressor?
On Atlas Copco’s mineral oil, every 4,000 hours or yearly, falling to 2,000 hours above 35 C ambient. Atlas Copco’s Roto Synthetic Fluid Xtend Duty runs 8,000 hours or 2 years in rooms up to 40 C; its Ultra fluid runs 6,000 hours up to 35 C. Check your manufacturer’s table.
How often should you drain an air compressor tank?
OSHA says “frequently”, often enough to stop liquid building up. Atlas Copco says daily, or confirm the automatic drain discharges.
Does OSHA require air compressor maintenance?
OSHA 1910.169 requires receiver drains, a pressure gauge and safety valves tested at regular intervals. 1910.147 governs lockout during servicing.
What does industrial air compressor maintenance include?
Oil and filter service, separator and air filter changes, belts, coolers, drains and leaks, safety valve testing and receiver inspection. All are on the checklist.
How often should I replace the air compressor filter?
Atlas Copco says replace the air filter element every 4,000 hours or yearly and clean it every 3 months. Line filters go when the pressure drop reaches 2 to 3 psid.
Related tools
Where Morsa fits
Know every compressor was checked and serviced on time.
Morsa asks the technician for the checklist, logs it against the compressor and flags what is missed or failed. It works in whatever your plant runs on: WhatsApp, Teams, email or text.

