Free tool

Conveyor maintenance checklist

Walk the line every day for tracking, noise and guards. Each week, check chain lubrication, oil levels and emergency stops. Each month, check belt tension and condition, guides and fasteners. Every quarter, check the drive and take-up, and every year, measure chain wear. Fill in the checklist below, then download it as a PDF (filled or blank) or an Excel file. This list covers belt, curve and chain conveyors; powered roller, motor-driven roller and sorter conveyors follow their maker’s schedule. Morsa asks for each check and flags a missed or failed one.

Updated November 12, 2026

Equipment and technician
Optional
Optional
Daily checks (5)
1.Walk the line: belt misalignment, edge fraying and drift; path clear of debris
Walk the line: belt misalignment, edge fraying and drift; path clear of debris
2.Listen for grinding, squealing or knocking; watch for excess vibration
Listen for grinding, squealing or knocking; watch for excess vibration
3.Check guards, pull cords and emergency stops are in place and not obstructed
Check guards, pull cords and emergency stops are in place and not obstructed
4.Look for visible wear on belts, chains, hinges, fasteners and splices
Look for visible wear on belts, chains, hinges, fasteners and splices
5.Check rollers and pulleys turn freely without wobble
Check rollers and pulleys turn freely without wobble
0 of 5 marked
Your own tasks (0)

Add tasks your site needs. They print with this checklist, on the full schedule and in Excel. 0 on this checklist, 0 of 15 used across the conveyor checklists.

Before you file it: 3 to fix
  • FixAdd the conveyor number, so the check is filed against the right conveyor.
  • FixAdd the technician's name.
  • FixAdd the date.
  • Check5 of 5 checks are not marked yet.
Show
Conveyor maintenance checklistDaily checksBelt, curve and chain-driven conveyors. Mark items that do not apply N/A. The maker's manual wins.Conveyor numberLocationRun hoursDateTechnicianCompany or siteReviewed byMark each check Done, Issue or N/A; a check with no N/A box applies to every unit. Write what is wrong against each issue and open a work order. Sourcenumbers refer to the list at the end.#Daily checksSourceDoneIssueN/AReading or note1Walk the line: belt misalignment, edge fraying and drift; path clear ofdebris72Listen for grinding, squealing or knocking; watch for excess vibration73Check guards, pull cords and emergency stops are in place and notobstructed54Look for visible wear on belts, chains, hinges, fasteners and splices75Check rollers and pulleys turn freely without wobble7Technician signatureWork orders openedReviewed by (maintenance lead)DateBased on:1. Interroll (Portec), PS249-PS271 belt curve manual, maintenance table (read 12 November 2026)2. Hytrol, SBC-SQ installation and maintenance manual, bulletin 757, August 2025 (read 12 November 2026)3. Dorner Conveyors, 3200 Series installation, maintenance and parts manual 851-781 (read 12 November 2026)4. Renold, Conveyor chain installation, maintenance and designer guide (read 12 November 2026)5. OSHA, 29 CFR 1910.219, Mechanical power-transmission apparatus, osha.gov (read 12 November 2026)6. OSHA, 29 CFR 1910.147, The control of hazardous energy, osha.gov (read 12 November 2026)7. FMH Conveyors, Conveyor preventive maintenance checklist (read 12 November 2026)Conveyor maintenance checklist: Daily checks.

Next, Morsa schedules this checklist, asks the technician for it from their phone, logs the result against the asset and flags any check that is missed or fails. Log what stops your conveyors or book a demo.

Blank conveyor forms to print:

1 page, letter size. 0 of 5 checks marked.

Runs in your browser. Nothing you type is uploaded; the check is saved only in this browser, and the PDF and Excel files are built on your device.

Conveyor maintenance schedule at a glance

How oftenWhat to checkSource
DailyTracking, noise, guards, stops, visible wearFMH Conveyors
WeeklyChain lubrication and oiler, reducer and motor, chain tension, stopsHytrol, Renold
MonthlyBelt tension and condition, alignment, guards, chain guides, fastenersInterroll, Dorner, Hytrol
Every 3 monthsDrive wear and tension, gearbox oil, end-roll bearings, chain take-upInterroll, Hytrol, Renold
Every 6 monthsReturn wheels, reducer serviceInterroll
YearlyBelt seams, end rolls, sprockets, chain guides, chain elongationInterroll, Renold

Intervals are from Interroll’s belt curve manual, Hytrol’s SBC-SQ manual, the Dorner 3200 manual and Renold’s chain guide. Your conveyor’s manual overrides them.

How to use the conveyor maintenance checklist

  1. Enter the conveyor number and run hours.

  2. Pick the checklist that is due and mark each check Done, Issue or N/A. Chain, curve and belt items are N/A when the conveyor does not have them. Guard and stop checks cannot be marked N/A.

  3. Write what is wrong against failed items, with where on the line.

  4. Download the PDF (filled or blank) or the Excel file for the maintenance log.

Conveyor belt maintenance: tension and tracking

Over-tightening is the common error. Dorner’s manual says tension should be “the minimum required to move loaded conveyor”, warns that over-tensioning causes “excessive pulley bearing load and early failure”, and says to retighten only when the belt slips or the tensioning spring shows more than 1/2 inch (12 mm) beyond its original setting. If proper tension cannot be reached before the out-of-tension indicator turns red, the belt must be replaced. For tracking, adjust the discharge end first. FMH Conveyors, a dealer, says to adjust belt tension weekly; we follow Dorner and check, not adjust, unless the belt slips.

Conveyor chain: lubrication, take-up and the wear test

Hytrol says to check chain lubrication weekly: the chain should look moist, and if oil drips from the tails the flow is too high. Renold’s guide lists a weekly lubrication check, take-up checks in the first month and every 3 months, and yearly checks of side plates, elongation, sprocket wear, shaft alignment and lubricant condition.

To measure chain wear, measure a length over as many pitches as you can, on a straight section under tension. Renold’s formula: percentage extension = (M minus X times P) divided by (X times P), times 100, where M is the measured length, X the number of pitches and P the pitch. As an example from our arithmetic, 10 pitches of 76.2 mm should measure 762 mm; if they measure 772 mm, extension is (772 minus 762) divided by 762, or 1.3 percent. Replace when the figure reaches the limit in the chain maker’s table, which depends on the series and the pitch.

Overhead conveyor maintenance

Renold’s chain guide covers overhead conveyors as well as floor-level ones. Its typical schedule applies: lubrication weekly, take-up in the first month and every 3 months, and a yearly elongation and sprocket check. Overhead systems with trolleys and power-and-free tracks have their own manufacturer schedules, which we did not read. Use the maker’s manual for trolleys, switches and lifts.

Guards, lockout and safety

  • Guards. OSHA 29 CFR 1910.219 says sprocket wheels and chains “shall be enclosed unless they are more than seven (7) feet above the floor or platform”. Overhead chain drives are guarded like overhead belts.

  • Lockout. Dorner: “LOCK OUT POWER before removing guards or performing maintenance.” OSHA 1910.147 requires isolation, relief of stored energy and verification.

  • Fasteners. Hytrol says to check set screw torque after the first 24 hours of operation on a new conveyor.

Where the conveyor sources disagree

Hytrol’s checklist does not give readable intervals, so we used its component list and its weekly lubrication statement, and took intervals from Interroll and Renold. Lubrication needs differ: Dorner’s 3200 bearings need none, Interroll says to grease curve end rolls quarterly. The manual for your conveyor settles it.

What to do when a conveyor check fails

  • Guard missing or stop fails: do not run the conveyor. Tag it out.

  • Isolate before work. Lock out and verify under OSHA 1910.147.

  • Belt will not hold tension: replace the belt; do not keep tightening.

  • Write the fault on the checklist, tell the maintenance lead and log the stoppage on the machine downtime log.

Conveyor maintenance mistakes

  1. Over-tensioning belts. It wears bearings early.

  2. Over- or under-lubricating chain. Dripping or dry are both wrong.

  3. Running with a guard off.

  4. Waiting for the chain to fail. Measure extension yearly.

  5. No record of what was found. Repeat faults point to alignment or loading.

Keeping the conveyor checklist on schedule

Morsa asks the line lead for the weekly check on each conveyor, by phone in WhatsApp, Teams, text or email, and files the answers against the conveyor. When a guard, a stop or the oiler check fails, Morsa tells the maintenance lead the same day. It schedules the quarterly and yearly work from run hours and calendar dates, for approval.

Other maintenance checklists

Frequently asked questions

How often should a conveyor be maintained?

Daily walk-through, weekly lubrication and oil checks, monthly belt and guard checks, a quarterly drive check and a yearly chain wear test.

How do you maintain a conveyor belt?

Keep tension at the minimum that moves the load, track from the discharge end, and check seams and condition monthly. Replace when tension cannot be held.

What is on a conveyor belt maintenance checklist?

Tracking, tension, seams, rollers and pulleys, guards, stops and drive checks, each with an interval. See the checklists above.

How do you check conveyor chain wear?

Measure a length over many pitches on a straight run under tension and compute percentage extension. Replace at the chain maker’s limit.

How often should overhead conveyor chain be lubricated?

Renold’s schedule checks lubrication weekly. Frequency varies with conditions, from daily to every one or two weeks.

Does OSHA require conveyor guarding?

OSHA 1910.219 requires sprockets and chains to be enclosed unless more than 7 feet above the floor, and 1910.147 covers lockout during service.

Where Morsa fits

Keep every conveyor checked and every guard on.

Morsa asks for the checklist, files it against the conveyor and flags a missed check or a failed guard or stop. It works in whatever your plant runs on: WhatsApp, Teams, email or text.

Machines, people, and vendors, finally in one. We start with yours.

For queries, feedback or suggestions

© 2026 Morsa. All Rights Reserved. A Product by Lunar.

Machines, people, and vendors, finally in one. We start with yours.

For queries, feedback or suggestions

© 2026 Morsa. All Rights Reserved. A Product by Lunar.

Machines, people, and vendors, finally in one. We start with yours.

For queries, feedback or suggestions

© 2026 Morsa. All Rights Reserved. A Product by Lunar.